Vacuum Blister Adhesive
Vacuum Blister Adhesive Product introduction of vacuum plastic adhesive: The vacuum forming adhesive is a milky white emulsion with very low viscosity and good spray performance. It can be used alone or with the addition of a bridging agent U6Z. Application range: Suitable for vacuum forming machine, bonding PVC film on MDF, particleboard
Influencing factors of curing speed of EVA hot melt adhesive
Influencing factors of curing speed of EVA hot melt adhesive The curing speed of EVA hot melt adhesive refers to the time from the beginning of sizing and pressing to 80% bond strength. The curing time required for general use ranges from 1 second to 10 seconds, and the curing speed required for
hot melt adhesive for filter
hot melt adhesive for filter Air filters are components used to purify the air. Filters are generally used in farms, laboratories, sterile rooms, car engines, car air conditioners, household air conditioners, household air purifiers, etc. 1. Hot melt adhesive for flat filter Generally, the common filter element is a high-efficiency filter in glass
Application and development trend of water-based adhesives
Application and development trend of water-based adhesives Water-based adhesives are environmentally friendly adhesives prepared from natural polymers or synthetic polymers as adhesives and water as solvent or dispersant to replace toxic organic solvents that pollute the environment. Water-based adhesives are mainly used in books, packaging, tapes, paper lamination, flooring and construction, shoemaking, automotive
Is it safe to fill tires with hot melt glue?
Is it safe to fill tires with hot melt glue? Filling tires with hot melt adhesive is one way to improve tire safety. It can greatly reduce the incidence of traffic accidents caused by flat tires. The tire upgrade is actually spraying a layer of hot melt glue on the inner wall. When
Influencing factors of curing speed of EVA hot melt adhesive
Influencing factors of curing speed of EVA hot melt adhesive The curing speed of EVA hot melt adhesive refers to the time from the beginning of sizing and pressing to 80% bond strength. The curing time required for general use ranges from 1 second to 10 seconds, and the curing speed required for
Causes of hot melt adhesive drawing
Causes of hot melt adhesive drawing Occasionally, there are a few filaments remaining when the nozzle is closed, causing equipment pollution, or adhering to the side of the guide bar, pressure plate, etc., which will cause problems to the appearance and operation of the box that needs to be packaged later. Influence. After
Perfect binding hot melt adhesive selection considerations
Perfect binding hot melt adhesive selection considerations There are many types of hot melt adhesives for book binding. In general, when choosing a hot melt adhesive for book binding, the following aspects should be considered: 1. The final use of the product; 2. Paper type: such as offset paper, coated paper, writing paper,
Six-minute gluing method of hot melt adhesive pellets
Six-minute gluing method of hot melt adhesive pellets Hot-melt adhesive pellets are a kind of plastic adhesive product. The physical state of hot-melt adhesive pellets changes with the temperature within a certain temperature range, but the chemical properties remain unchanged. Hot-melt adhesive pellets are non-toxic and tasteless. , How many do you know
The importance of surface treatment in the bonding process of adhesives
The importance of surface treatment in the bonding process of adhesives The quality of the surface treatment is often the key to the success or failure of a good adhesive joint, because the wettability of the adhesive to the surface of the adherend and the intermolecular force at the interface (that is, the
Can hot melt glue stick to books?
Can hot melt glue stick to books? The use of hot melt adhesive to stick books has been used very maturely, no matter thick or thin books can be glued, but many people do not pay much attention to the application of hot melt adhesive on weekdays. Hot melt glue is not as
The solution to the easily broken hot melt adhesive layer
The solution to the easily broken hot melt adhesive layer The reason why the adhesive layer is easy to break is related to the force and the physical properties of the hot melt adhesive. In the final analysis, it is necessary to use the hot melt adhesive to find the corresponding solution. Why